UltiMaker 2 Extended+ Print Cost Calculator
Digital manufacturing cost model for the UltiMaker 2 Extended+ (FDM). Covers typical power draw (~150W), machine depreciation ($0.416/hr), material usage, and commercial quoting margins.
Commercial Quote & Margin Engine
Calculate retail client selling price and estimated profit.
UltiMaker 2 Extended+ Hardware Specifications
Build volume is taken from published slicer profiles. Power draw is a class-based estimate for this size and category of machine, not a manufacturer rating. Service life is a class-based assumption for this size and category of machine, not a manufacturer rating. The price shown is a hand-checked typical street price rather than an official MSRP.
Understanding UltiMaker 2 Extended+ Running Costs
How FDM affects the numbers
FDM machines draw power in bursts rather than continuously. The hotend and heated bed cycle on and off to hold temperature, so the average figure used here sits well below the peak nameplate rating — the bed is usually the single largest consumer, which is why enclosed and large-bed machines cost noticeably more per hour to run.
Motion system: Cartesian
A bedslinger moves the plate back and forth on the Y axis, which puts a practical ceiling on acceleration: past a certain speed the part itself becomes the thing being thrown around. For quoting that means print times scale fairly predictably with part height and layer count, but tall, narrow parts are the risk case — the taller the part, the more the moving bed works against it, and a toppled print late in a long job is the classic cause of an unbudgeted reprint.
Power draw: 150 W
A draw in the 100–250 W band is typical of open-frame desktop machines. Power is a genuine but secondary line item: worth including for accurate quoting, not worth optimizing. A standard 15 A household circuit will run several of these simultaneously without trouble.
No heated chamber: what it can print
This machine has no actively heated chamber, so the bed is the only meaningful heater and the energy line on a typical job stays low. That is a materials constraint before it is a cost one: PLA, PETG and TPU are comfortable, while ABS, ASA and polycarbonate are warp-prone on large parts. If the machine is enclosed, passive heat retained from the bed helps considerably and many people run ABS successfully; on an open frame the failure rate on big parts in those materials is high enough that the usual 8–10% buffer understates the real risk.
What dominates the hourly rate
At this page’s default rate of $0.16/kWh, depreciation is the larger share of this machine’s hourly rate, so the assumed lifespan drives your cost more than your electricity tariff does. If you service the machine well and expect to exceed the default hours, raise the lifespan figure in the calculator — it will lower your quoted cost more than any energy saving could.
Quoting at this price point
Industrial equipment recovers its cost only through utilization, and the depreciation figure here will overwhelm every other modeled input. Real-world ownership adds items this calculator does not cover: service contracts, calibration, trained operators, facility requirements, and consumables. Treat the output as a floor for machine time and layer your actual overhead on top.
Owning an UltiMaker machine
Industrial machines are bought as production equipment, and the sticker price is only part of the cost of ownership. Expect service contracts, scheduled calibration, trained operators and validated material supply — none of which this calculator models. The hourly rate below is a floor for machine time; the real number for a commercial quote is that figure plus your own overhead, and it is usually the larger half.
Build volume: 15,167 cm³
A standard desktop envelope handles the large majority of hobby and small-commercial work without splitting parts. For quoting purposes this is the most predictable size class: heat-up time, energy draw, and failure risk all scale roughly with print duration rather than part geometry.
UltiMaker 2 Extended+ Operating Cost by Print Duration
Pre-calculatedEstimated electricity cost (at $0.16/kWh) and hardware depreciation over print duration. Excludes material and labor.
| Print Duration | Energy (kWh) | Electricity Cost | Depreciation | Total Machine Cost |
|---|---|---|---|---|
| 1 Hour | 0.15 kWh | $0.02 | $0.42 | $0.44 |
| 4 Hours | 0.6 kWh | $0.10 | $1.66 | $1.76 |
| 8 Hours | 1.2 kWh | $0.19 | $3.33 | $3.52 |
| 12 Hours | 1.8 kWh | $0.29 | $4.99 | $5.28 |
| 24 Hours | 3.6 kWh | $0.58 | $9.98 | $10.56 |
| 100 Hours | 15 kWh | $2.40 | $41.58 | $43.98 |
Frequently Asked Questions
How much electricity does the UltiMaker 2 Extended+ use?
The UltiMaker 2 Extended+ runs at a typical draw of roughly 150 watts during active printing. Power draw is a class-based estimate for this size and category of machine, not a manufacturer rating. At the standard residential electricity rate of $0.16 per kWh, running this printer costs approximately $0.024 per hour in power. A 10-hour print consumes ~1.50 kWh (about $0.24 in electricity).
What is the depreciation rate for the UltiMaker 2 Extended+?
At a researched street price of $2495 and an assumed service life of 6,000 printing hours, the machine depreciation rate works out to roughly $0.416 per operating hour. Including this in your print quotes ensures hardware replacement and maintenance costs are recovered.
What is the combined machine running cost per hour for the UltiMaker 2 Extended+?
Combining estimated power consumption ($0.024/hr) and equipment depreciation ($0.416/hr), the baseline operating cost for the UltiMaker 2 Extended+ works out to roughly $0.44 per hour (excluding raw filament/resin and operator labor).
Is electricity or depreciation the bigger cost on the UltiMaker 2 Extended+?
At this page’s default rate of $0.16/kWh, depreciation is the larger share of this machine’s hourly rate, so the assumed lifespan drives your cost more than your electricity tariff does. If you service the machine well and expect to exceed the default hours, raise the lifespan figure in the calculator — it will lower your quoted cost more than any energy saving could.
What should I know about running the UltiMaker 2 Extended+ (FDM) commercially?
A draw in the 100–250 W band is typical of open-frame desktop machines. Power is a genuine but secondary line item: worth including for accurate quoting, not worth optimizing. A standard 15 A household circuit will run several of these simultaneously without trouble. Industrial equipment recovers its cost only through utilization, and the depreciation figure here will overwhelm every other modeled input. Real-world ownership adds items this calculator does not cover: service contracts, calibration, trained operators, facility requirements, and consumables. Treat the output as a floor for machine time and layer your actual overhead on top.
How does the UltiMaker 2 Extended+'s Cartesian motion system affect print cost?
A bedslinger moves the plate back and forth on the Y axis, which puts a practical ceiling on acceleration: past a certain speed the part itself becomes the thing being thrown around. For quoting that means print times scale fairly predictably with part height and layer count, but tall, narrow parts are the risk case — the taller the part, the more the moving bed works against it, and a toppled print late in a long job is the classic cause of an unbudgeted reprint.
Can the UltiMaker 2 Extended+ print ABS or polycarbonate without a heated chamber?
This machine has no actively heated chamber, so the bed is the only meaningful heater and the energy line on a typical job stays low. That is a materials constraint before it is a cost one: PLA, PETG and TPU are comfortable, while ABS, ASA and polycarbonate are warp-prone on large parts. If the machine is enclosed, passive heat retained from the bed helps considerably and many people run ABS successfully; on an open frame the failure rate on big parts in those materials is high enough that the usual 8–10% buffer understates the real risk.
How do I calculate commercial quotes for 3D prints on a UltiMaker 2 Extended+?
To calculate a profitable quote: (1) calculate filament or resin consumed, (2) add the machine operating cost (~$0.44/hr × print time), (3) add labor preparation time, (4) apply an 8%–10% risk buffer for print failures, and (5) apply your target retail profit margin (typically 40%–60%).
Calculate maximum melt zone limits (mm³/s) to prevent underextrusion on high-speed prints.
Material Densities Filament Weight & Length Directory →Look up densities and spool tare deductions for PLA, PETG, ABS, and engineering polymers.